Monkey Puzzle Bowl Part 2 Обезьяна головоломки Bowl часть 2

Hi Everyone,

Im still working on the monkey puzzle bowl from yesterday-the first thing I did was to flatten the sides of the exterior of the bowl:

Привет всем,

Я все еще работаю на чаше головоломки обезьяны со вчерашнего дня, первое, что я сделал,чтобы сгладить стороны внешность чаши:

I gave the outside a good sanding and then I flipped over the bowl to begin to hollow out the interior. I want the interior shape to reflect the two flat sections of the exterior of the bowl so Im hollowing out the bowl in sections. You can see this in the next two photos:

Я отдал за пределами хорошо шлифование, а затем я перевернул миску, чтобы начатьдолбить из интерьера. Я хочу, чтобы интерьер форме с учетом двух плоских участковвнешность чаши, так что я размывание чашу в секциях. Вы можете увидеть это в ближайшиедве фотографии:

After about 45 minutes of turning, the interior was hollowed out-there is the bottom section, the middle section, and the rim. They correspond to the exterior shape of the bowl:

Примерно через 45 минут после поворота, интерьер выдолбленные-есть нижнюю часть,среднюю часть и края. Они относятся к внешней форме чаши:

I sanded the bowl for about 30 minutes and then stopped and took the following photo:

Я отшлифовать чашу в течение примерно 30 минут, а затем остановился и принял следующее фото:

and Im not so sure I like the interior shape. Im going to think about this and I may remove it and leave the bowl with a more rounded interior.

и я не уверен, что мне нравится внутренняя форма. Я буду думать об этом, и я могу удалить его и оставить миску с более округлыми интерьера.


As the bowl needs more sanding Im going to think about this over night and Ill work on it more on Monday.

See you then.

VW

В миску нужно больше шлифования я собираюсь думать об этом всю ночь, и я буду работать на нем более в понедельник.

Увидимся.

Виктория

Read More

Scrap Wood Project Veggie and Dip Bowl

Hi Everyone,

Well, the block that I made yesterday is dry and solid so lets turn it into a bowl!

Heres the photos:

Here is the block, dried and with the clamps off. Ive located the center, drawn a circle. Lets go and cut it out on the bandsaw:

This is the blank on the lathe. You can see how uneven and gluey it is. I love turning laminated blocks as you go from rough mess to finished bowl and you really never know what it all is going to look like until youre done:

Here is the underside of the bowl after all the rough glued surface has been cut away:

The underside of the bowl is going to have a broad, flat foot. Here Ive marked out the foot and the center mortise:

In this photo you can see how the edges and the foot have been trued up and flattened:

And here is the underside. Im done cutting this part of the bowl. Next, Ill sand it smooth:

The sides of the bowl are going to be gently curved. I want to keep the bowl as close to its original shape so as to preserve as much of the interior volume as I can. Here you can see the sides rough and in need of shaping:

I drew a line down the center of the side and Im going to cut to arcs that will meet in the middle. One arc will start on the right edge and curve towards the middle and the other will begin at the left hand edge:

And here we are with the exterior wall of the bowl shaped and smoothed. Time to flip the bowl over and begin hollowing it out:

The bowl will have two sections: a center section that will hold a small bowl for dip and a larger section that will hold cut veggies. Here Ive smooth off the top of the blank:

In this photo Ive marked off the waste areas-these are the areas that will be removed:

I did a little hollowing of the bowl and then I stopped as its getting cold and windy outside. Here is the bowl partially hollowed out. When Im done the center will be deep enough to hold a dip bowl and there will be enough room for cut veggies:

Tomorrow Ill finish hollowing it and sand it smooth and well talk about finishes.

VW

Read More